Transcription

Owner’s Manual Model: AW1120ESave these instructions. This manual will help you to obtainefficient, dependable service from the heater, and enableyou to order repair parts correctly. Keep in a safe place forfuture reference.SAFETY NOTICE:If this heater is not properly installed, a house fire may result.For your safety, follow the installation instructions. Neveruse make-shift compromises during the installation of thisheater. Contact local building or fire officials about permits,restrictions and installation requirements in your area.CAUTION!Please read this entire manual before you install or use yournew room heater. Failure to follow instructions may result inproperty damage, bodily injury, or even death. ImproperInstallation Could Void Your Warranty!United States Stove CompanyPO Box 151, 227 Industrial Park Rd.,South Pittsburg, TN 37380PH: (800) 750-2723www.usstove.comRReport Number: F19-473Tested Per EPA Methods ALT-125, ASTME2515, ASTM E3053 and CSA B415Certified to UL 1482-2011 (R2015) andULC-S627-00 (R2016)Approved for mobile home installationin USA and CanadaU.S. Environmental Protection AgencyCertified to comply with 2020Ce produit peut vous exposer à des agents chimiques, y compris au monoxyde decarbone,lesquels sont reconnusdans l’État de lastandards.Californie comme causant le cancer etparticulateemissionsdes malformations congénitales ou autres dommages au fœtus. Pour obtenir plus derenseignements, veuillez consulter le site www.P65warnings.ca.govCALIFORNIA PROPOSITION 65 WARNING:This product can expose you to chemicals including carbon monoxide, whichis known to the State of California to cause cancer, birth defects and/or otherreproductive harm. For more information, go to www.P65warnings.ca.gov853573B-4203i

This manual describes the installation and operation of the Ashley, AW1120E wood heater. This heater meetsthe 2020 U.S. Environmental Protection Agency’s cordwood emission limits for wood heaters sold after May 15,2020. Under specific test conditions this heater has been shown to deliver heat at rates ranging from 15,196 to40,594 Btu/hr with 1.7 g/hr and 69% efficiency. Note: The BTU ratings mentioned above are based on the EPA testprotocol under specific test conditions. Our advertised BTU’s are based on the first hour of operation at high burnrate burning dry cordwood.Combustible:WoodColors:Metallic BlackFlue Pipe Diameter:6” (153 mm)Flue Pipe Type: (Standard Single Wall or Double Wall):Black or Blued Steel 2100 F (650 C)Minimum Chimney Height:12’ (3.7 m)Maximum Log Length:18” (458 mm)Electrical:120VAC, 0.55A, 60HzDimensionsOverall: Depth x Width x Height:AW1120E-BL21.3” x 24.6” x 30.9” (542 mm x 625 mm x 785 mm)AW1120E-BP21” x 22.5” x 31.7” (534 mm x 572 mm x 806 mm)Combustion Chamber: Width x Depth:18.25” x 11.5” (464 mm x 293 mm)Firebox Volume: Cubic Feet:1.31 cubic feetDoor Opening: Width x Height:16” x 9” (407 mm x 229 mm)Pyroceramic Glass Door: (Viewing) Width x Height:14.4” x 7.9” (366 mm x 201 mm)CAUTIONS: HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE SKINBURNS. DO NOT USE CHEMICALS OR FLUIDS TO IGNITE THE FIRE. DO NOT LEAVE THE STOVE UNATTENDED WHEN THE DOOR IS SLIGHTLY OPENED. DO NOT BURN GARBAGE, FLAMMABLE FLUID SUCH AS GASOLINE, NAPHTHA OR MOTOR OIL. DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM. ALWAYS CLOSE THE DOOR AFTER THE IGNITION.Note: Register your product on line at www.usstove.com. Save your receipt with your records for any claims.-2-

UNPACK AND INSPECTAssemblyRemove the packing from the appliance and inspect for any damage. Your appliance is packed with the doorhandle spring not installed. Ensure that the bricks are positioned correctly and not broken (see illustration forproper brick arrangement). Make sure that the baffle board, above the air tubes, is in place and undamaged.(DO NOT REMOVE).BLOWER ASSEMBLYFLUE COLLAR ASSEMBLYNOTE: The B36 blower may be purchased separatelyif not equipped.The blower assembly must be disconnected fromthe source of electrical supply before attemptingthe installation. The blower assembly is intended foruse only with a stove that is marked to indicate suchuse. Do not route the supply cord near or across hotsurfaces! Fix the assembly to the back of the stovewith the four screws provided.Mount the flue collar to the top of the unit as shownusing the (3) 5/16-18 x 1-1/2 bolts, (3) washers, and(3) weld tabs provided in the parts box.5/16-18 x 1-1/2BOLTWASHERGASKETHEATERTOPWELDTABFIREBRICK CONFIGURATIONReplace the Firebrick as shown in the illustration.ASH PAN ASSEMBLYRemove ash pan from firebox. Under the firebox,there are two brackets; Slide the ash pan into thesebrackets.-3-

InstallationSAFETY NOTICE IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE, FOLLOWTHE INSTALLATION INSTRUCTIONS. CONSULT YOUR MUNICIPAL BUILDING DEPARTMENT OR FIRE OFFICIALS ABOUT PERMITS, RESTRICTIONS ANDINSTALLATIONS REQUIREMENTS IN YOUR AREA. USE SMOKE DETECTORS IN THE ROOM WHERE YOUR STOVE IS INSTALLED. KEEP FURNITURE AND DRAPES WELL AWAY FROM THE STOVE. NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR SIMILARLIQUIDS TO START OR “FRESHEN UP” A FIRE IN THIS HEATER. KEEP ALL SUCH LIQUIDS WELL AWAY FROM THEHEATER WHILE IT IS IN USE. IN THE EVENT OF A CHIMNEY FIRE, PUSH THE AIR CONTROL FULL CLOSED TO DEPRIVE THE FIRE OF OXYGEN.CALL THE FIRE DEPARTMENT. DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM. A SOURCE OF FRESH AIR INTO THE ROOM OR SPACE HEATED SHALL BE PROVIDED WHEN REQUIRED.POSITIONING THE STOVEIt is very important to position the wood stove as close as possible to the chimney, and in an area that will favorthe most efficient heat distribution possible throughout the house. The stove must therefore be installed in theroom where the most time is spent, and in the most spacious room possible. Recall that wood stoves produceradiating heat, the heat we feel when we are close to a wood stove. A wood stove also functions by convection,that is through the displacement of hot air accelerated upwards and its replacement with cooler air. If necessary,the hot air distribution from the stove may be facilitated by the installation of a blower. The wood stove must notbe hooked up to a hot air distribution system since an excessive accumulation of heat may occur. A wood stovemust never be installed in a hallway or near a staircase, since it may block the way in case of fire or fail to respectrequired clearances.FLOOR PROTECTORJThis heater must have a non-combustible floor protector (emberprotection) installed beneath it if the floor is of combustible material.If a floor pad is used, it should be UL listed or equal. The floor pador non-combustible surface should be large enough to extendunder the stove and beyond each side as indicated. If there isa horizontal run of flue pipe, there needs to be floor protectionunder it that extends two inches beyond either side of the 04LRight8204HK* Canadian installations require 18” (457mm)-4-LFLOOR PROTECTOR DIMENSIONS

CLEARANCES TO COMBUSTIBLESIt is of utmost importance that the clearances to combustible materials be strictly adhered to during installationof the stove. Refer to the provided tables:BackwallCeilingCLEARANCE TO WALLSSide wallSide wallBackwallCORNER INSTALLATIONCLEARANCE TOWALLS & CELINGCORNER INSTALLATIONCLEARANCE TO WALLS Do not place any combustible material within 4’(1.2m) of the front of the unit. The clearance between the flue pipe and a wallare valid only for vertical walls and for vertical fluepipe. The chimney connector must not pass through anattic or roof space, closet or similar concealedspace, a floor, or a ceiling. For Canadian installations, where passage througha wall, or partition of combustible constructionis desired, the installation must conform to CAN/CSA-B365. A flue pipe crossing a combustible wall must have aminimum clearance of 18” (457.2mm). To reduce flue clearances from combustiblematerials, contact your local safety department.KeyDimensionsInchmmABackwall to Stove17432BSidewall to Stove21534CWall to corner (Angled Installation)14356DCeiling Height842134EBackwall to Flue20508FSidewall to Flue29737GWall to Flue (Angled Installation)22559SPECIAL MOBILE HOME REQUIREMENTSWARNING! - Do not install in a sleeping roomCAUTION! - The structural integrity of the mobile home floor, wall, and ceiling/roof must be maintained.In addition to the previously detailed installation requirements, mobile home installations must meet the followingrequirements: The space heater is to be connected to a factory-built chimney conforming to CAN/ULC-S629, Standard for650 C Factory-Built Chimneys. The heater must be permanently attached to the floor. There are two holes in the pedestal base, use 3/8” boltsthrough the floor. The heater must be electrically grounded to the steel chassis of the mobile home with 8 GA copper wire usinga serrated or star washer to penetrate paint or protective coating to ensure grounding. When moving your mobile home, all exterior venting must be removed while the mobile home is beingrelocated. After relocation, all venting must be reinstalled and securely fastened. Outside Air is mandatory for mobile home installation. See your dealer for purchasing. Check with your local building officials as other codes may apply. Only use the specified components listed in this manual for this unit. The use of components that are not meantfor this unit can cause unsafe conditions.COMBUSTION AIR ASSEMBLY INSTRUCTIONS (MOBILE HOME INSTALLATIONS - REQUIRED)This appliance requires a source of combustion air. If your home is of tight construction or has negative pressureproblems, you will need an outside source of air. Below is a list of possible indicators that a source of outsidecombustion air may be required.-5-

Your stove does not draw steadily, smoke rollout occurs, wood burns poorly, or back-drafts occur whether ornot there is combustion present. Existing fuel-fired equipment in the house, such as fireplaces or other heating appliances, smell, do not operateproperly, suffer smoke roll-out when opened, or back-drafts occur whether or not there is combustion present. Opening a window slightly on a calm (windless) day alleviates any of the above symptoms. The house is equipped with a well-sealed vapor barrier and tight fitting windows and/or has any powereddevices that exhaust house air. There is excessive condensation on windows in the winter. A ventilation system is installed in the house.If an outside air intake is required, you may purchase a standard 4” Dryer Vent kit from your local hardware supplystore and install it on the rear of the appliance.When using a Dryer venting kit, the outlet cover must be of a design that DOES NOT close by means of a flap ortrap door. You must purchase a style that allows a continuous in-flow of air and that has a rodent screen. Thisadapter can be purchased from your dealer.4FAK INSTALLATIONFollow the manufacturer’s installation instructions for attaching the dryer vent kit to the home. Then, attach it tothe adapter on the combustion air inlet on the back of the pedestal as shown.“Dryer Venting Kit”InstallationSlide the hose clamp over the aluminium flex pipe. Then slide theflex pipe over the air intake tube of the stove. Next tighten the hoseclamp over the end of the aluminium flex hose.SECURING APPLIANCE’S ON A PEDESTAL TO THE FLOORUse the designated holes to secure the unit to the floor.SECURING APPLIANCE’S WITH LEGS TO THE FLOOR1. The bracket engages around the square extrusionof the leveling bolt inserted into the leg.2. Once appliance is leveled, position the bracketand attach to the floor using the appropriatehardware needed for your specific flooring.3. Install one bracket per leg or consult your localauthority having jurisdiction to determine howmany points of attachment are required.-6-

CHIMNEY CONNECTOR (STOVE PIPE)The chimney connector and chimney must have the same diameteras the stove outlet (6”). If this is not the case, we recommend youcontact your dealer to ensure there will be no problem with thedraft. The stovepipe must be made of aluminized or cold roll steeland have a minimum thickness of 0.021” or 0.53mm. It is strictlyforbidden to use galvanized steel. The smoke pipe should beassembled to promote the male section (crimped end) of thepipe to be faced down. Attach each section to another with threeequidistant metal screws. The pipe must be short and straight.ToAll sections installed horizontally must slope at least 1/4 inch perAppliancefoot, with the upper end of the section toward the chimney. Anyinstallation with a horizontal run of chimney pipe must conformto NFPA 211. Contact NFPA (National Fire Protection Association) and request the latest edition of the NFPAStandard 211. To ensure a good draft, the total length of the coupling pipe should never exceed 8’ to 10’ (2.4m to3.04m). Except for cases of vertical installation, in a cathedral-roof style where the smoke exhaust system can bemuch longer and connected without problem to the chimney at the ceiling of the room. There should never bemore than two 90 degrees elbows in the smoke exhaust system. The installation of a “barometric draft stabilizer”(fireplace register) on a smoke exhaust system is prohibited. Furthermore, the installation of a draft damper is notrecommended. With a controlled combustion wood stove, the draft is regulated upon intake of the combustionair in the stove and not at the exhaust.IMPORTANCE OF PROPER DRAFTDraft is a force that moves air from the appliance up through the chimney. The amount of draft in your chimneydepends on the length of the chimney, local geography, nearby obstructions and other factors. Too much draftmay cause excessive temperatures in the appliance. An inadequate draft may cause back-puffing into theroom and ‘plugging’ of the chimney. An inadequate draft will cause the appliance to leak smoke into the roomthrough appliance and chimney connector joints. An uncontrollable burn or excessive temperature indicates anexcessive draft.CHIMNEYYour wood stove may be hooked up with a 6” factorybuilt or masonry chimney. If you are using a factorybuilt chimney, it must comply with UL 103 or CSA-B365standard; therefore it must be a Type HT (2100 F). Itmust be installed according to the manufacturer’sspecifications. Take into account the chimney’slocation to ensure it is not too close to neighbors orin a valley which may cause unhealthy or nuisanceconditions. If you are using a masonry chimney, itmust be built in compliance with the specifications ofthe National Building Code. It must be lined with fireclay bricks, metal or clay tiles sealed together with firecement. Round flues are the most efficient. The interior diameter of the chimney flue must be identical to thestove smoke exhaust. A flue which is too small may cause draft problems, while a large flue favors rapid coolingof the gas, and hence the build-up of creosote and the risk of chimney fires. Note that it is the chimney and notthe stove which creates the draft effect; your stove’s performance is directly dependent on an adequate draftfrom your chimney. Do not connect this unit to a chimney flue serving another appliance.The following recommendations may be useful for the installation of your chimney:1. It must rise above the roof at least 3’ (0.9m) from the uppermost point of contact.2. The chimney must exceed any part of the building or other obstruction within a 10’ (3.04m) distance by aheight of 2’ (0.6m).3. The installation of an interior chimney is always preferable to an exterior chimney. Indeed, the interiorchimney will, by definition, be hotter than an exterior chimney, being heated up by the ambient air in thehouse. Therefore the gas which circulates will cool more slowly, thus reducing the build-up of creosote andthe risk of chimney fires.4. The draft caused by the tendency for hot air to rise will be increased with an interior chimney.5. Using a fire screen at the extremity of the chimney requires regular inspection to ensure that it is not obstructedthus blocking the draft, and it should be cleaned when used regularly.-7-

FACTORY BUILT CHIMNEYWhen a metal prefabricated chimney is used, the manufacturer’sinstallation instructions must be followed. You must also purchase(from the same manufacturer) and install the ceiling supportpackage or wall pass-through and “T” section package, firestops(where needed), insulation shield, roof flashing, chimney cap, etc.Maintain proper clearance to the structure as recommendedby the manufacturer. The chimney must be the required heightabove the roof or other obstructions for safety and proper draftoperation.MASONRY CHIMNEYEnsure that a masonry chimney meets the minimumstandards of the National Fire Protection Association(NFPA) by having it inspected by a professional. Makesure there are no cracks, loose mortar or other signs ofdeterioration and blockage. Be sure to the chimneycleaned before the stove is installed and operated.When connecting the stove through a combustible wallto a masonry chimney, special methods are needed.-8-

COMBUSTIBLE WALL CHIMNEY CONNECTOR PASS-THROUGHSConduit de cheminéeConduit de cheminéeConduit decheminéeVide d’airConduit de cheminéeMETHOD A - 12” (304.8 mm) Clearance to Combustible WallLe dégagement minimum de la cheminée à la brique et lesmatériaux combustibles est de 5 cm (2 po) (50,8 mm)Member: Using a minimum thickness 3.5” (89 mm) brickand a 5/8” (15.9 mm) minimum wall thickness clay liner,Dégagement minimumconstruct a wall pass-through. The clay liner must conformde 30 cm (12 po,304,8 mm)to ASTM C315 (Standard Specification for Clay Fire Linings)des briquesor its equivalent. Keep a minimum of 12” (304.8 mm) of brickmasonry between the clay liner and wall combustibles. Theclay liner shall run from the brick masonry outer surface toConduit dethe inner surface of the chimney flue liner but not past theraccordementinner surface. Firmly grout or cement the clay liner in placeDoublage en30 cm (304,8 mm, 12 po)argile réfractaireto the chimney flue liner.Cheminée enminimum aux matériauxmaçonneriecombustiblesMETHOD B - 9” (228.6 mm) Clearance to Combustible WallMember: Using a 6” (152.4 mm) inside diameter, listed,Le dégagement minimum de la cheminée à la brique et lesfactory-built Solid-Pak chimney section with insulationmatériaux combustibles est de 5 cm (2 po) (50,8 mm)of 1” (25.4 mm) or more, build a wall pass-through with aDégagement minimumminimum 9” (228.6 mm) air space between the outer wall ofde 5 cm (9 po)Longueur deNonsoluble(228,6 mm)cheminée préfabriquée refractorythe chimney length and wall combustibles. Use sheet metalConduit decementsupports fastened securely to wall surfaces on all sides,raccordementto maintain the 9” (228.6 mm) air space. When fasteningUtiliser des piècesMinimum Vide d’airde cheminéesupports to chimney length, do not penetrate the chimneyde 5 cm (9 po)fabriquées pour(228,6mm)liner (the inside wall of the Solid-Pak chimney). The inner endle fixer solidementLongueur de cheminéeau raccordement.of the Solid-Pak chimney section shall be flush with the insideà égalité avec le conduitLongueur dedefuméeintérieurof the masonry chimney flue, and sealed with a non-watercheminéeCheminée en maçonneriesoluble refractory cement. Use this cement to also seal topréfabriquée etSupports derépertoriée, àthe brick masonry penetration.tôle d'acierisolant solide.METHOD C - 6” (152.4 mm) Clearance to Combustible WallDeux canaux d’aérationMember: Starting with a minimum 24 gage (.024” [.61 mm])Le dégagement minimum de la cheminée auxde 2,5 cm (1 po)supports en tôle d’acier et aux matériaux6” (152.4 mm) metal chimney connector, and a minimumchacun. (25,4 mm)combustibles est de 5 cm (2 po). (50,8 mm)Fabriqués en24 gage ventilated wall thimble which has two air channelsDeux canaux d